 |
   Edelbrock 1489 carburetor calibration kit.
For the Edelbrock 1411 carburetor.
Includes an assortment of needles and jets, one pair of metering rod retaining springs and a complete set of step-up springs.
This kit makes it easy to custom tune your Edelbrock carburetor to your specific engine setup by having the required parts on hand.
Later on, should you decide to change your engine setup, chances are you will have the required parts at hand, ready to install.
Image is not application specific.
METERING RODS: .070 x .042----.073 x .037----.073 x .042----.075 x .037
JETS: .104----.107----.110----.113

|
 |
 |
   Edelbrock 8089 banjo fuel inlet fitting.
Replaces the original fuel inlet fitting and allows the use of low profile air cleaners.
5/8-20 male to 3/8 hose barb.

|
 |
 |
   Edelbrock 8087 fuel inlet fitting.
5/8-20 male to -6AN male fuel inlet fitting for Edelbrock carburetors.
This fitting replaces the original fuel inlet fitting and allows the use of -6AN hose fittings.

|
 |
 |
   Edelbrock 8090 fuel lnlet fitting.
Replacement fuel inlet fitting for Edelbrock carburetors.
5/8-20 male to 3/8" female inverted flare.

|
 |
 |
   Edelbrock 1483 Ford throttle lever adapter.
Designed for Ford automatic transmission equipped vehicles with cable operated throttle.
(Will not fit A.O.D.) Accepts cruise control.
Mounts to the Edelbrock carburetors linkage.
Use with appropriate Edelbrock throttle linkage plate (available on this website).

|
 |
 |
   Edelbrock 1491 Ford 351W throttle cable adapter plate.
This plate repositions the stock throttle cable bracket to align with Edelbrock carburetor throttle arms.
Use with Edelbrock throttle lever adapter part number 1483 (available on this website) and the stock throttle cable bracket.
Designed for Ford 351W with cable activated throttle and automatic transmission kickdown rod.
Gold iridted finish.

|
 |
 |
   Edelbrock 1495 Ford 429 and 460 throttle cable plate.
Repositions the stock throttle cable brackets to align with the Edelbrock carburetors throttle arm.
Use with Edelbrock throttle lever adapter part number 1483 (available on this site).
Designed for Ford with cable activated throttle and automatic transmission kickdown rod.
Gold iridited finish.

|
 |
 |
   Edelbrock 1493 Ford 351M and 400 throttle cable plate.
Repositions the stock throttle cable brackets to align with the Edelbrock carburetors throttle linkage.
Use with Edelbrock throttle lever adapter part number 1483 (available on this site).
Designed for Fords with cable activated throttle and automatic transmission kickdown rod.
Gold iridited finish.

|
 |
 |
   Edelbrock 1490 Ford 289 and 302 throttle cable bracket.
Mounts to the intake manifold to correctly position the throttle cable in relation to the Edelbrock caburetors throttle linkage.
Gold iridite finish.

|
 |
 |
   Edelbrock 8011 Ford automatic transmission kick down rod extension.
For use with Edelbrock carburetors when the kick down rod is to short to reach.

|
 |
 |
   Edelbrock 8012 Chevrolet throttle cable and automatic transmission kick down cable extension kit.
Mounts to the carburetors throttle linkage for when the cable is not quite long enough.
Includes throttle ball stud for use with some universal throttle cables.

|
 |
 |
   Chrysler Dodge throttle linkage adapter by Edelbrock 1481.
Fits 1966 and newer Chrysler, Plymouth and Dodge.
Attaches to the Edelbrock carburetors throttle lever.
Accepts cruise control.
Use with the appropriate throttle cable plate (available on this website).
Gold iridite finish.

|
 |
 |
   Edelbrock 8003 Chrysler automatic transmission kick down rod extension.
Fits the Chrylser 1/4" diameter rod.
For use with Edelbrock carburetors, when the rod is to short to hook up.

|
 |
 |
   Edelbrock 1475.
Edelbrock carburetor accelerator pump nozzles.
Fits all Performer, Thunder and Performer EPS carburetors.
Includes .024, .033 and .043 nozzles and gaskets.

|
 |
 |
   Edelbrock carburetor metering rods.
These metering rods are designed for use with Edelbrock Performer Series and Thunder Series AVS carburetors.
An aid in tuning the carburetor to your engines fuel needs.
Sold in pairs.
Scroll the applications box to find your size.

|
 |
 |
   Edelbrock 1464.
Edelbrock carburetor step-up spring assortment.
For use with all Edelbrock Performer Series, Thunder AVS Series and Performer EPS Series carburetors.
Includes 5 spring sets to aid in tuning.
Each spring set includes 2 springs, for a total of 10 springs.
A 3"HG blue spring, a 4"HG yellow spring, a 5"HG orange spring, a 7"HG pink spring and a 8"HG plain spring.

|
 |
 |
   A carburetor heat insulating divided base gasket. Designed for use with the Edelbrock carburetor shown above.
Extra thick, .0320 to insulate the carburetor from heat to provide a cooler, denser fuel mixture for more power.
While the Edelbrock carburetor above comes with a thin base gasket, this extra thick heat insulating gasket allows the carburetor to run cooler which provides a denser fuel mixture for more power.
Includes longer carburetor mounting studs to provide for the additional thickness of the gasket.
Available for both a divided gasket (#9266) for use with dual plane intake manifolds and an open center gasket (#9265) for use with single plane intakes.
Find your style in the applications drop down box.

|
 |
 |
   Edelbrock 8036 bracket.
Provides a Chevy mounting bracket for the throttle cable, Turbo 350 kickdown cable and cruise control cable.
Fits Chevy small block.
All three positions are fully length adjustable.
Mounts to the back intake manifold bolts on the drivers side of the engine.
Super sturdy, heavy metal design.
Durable gold iridited quality finish.

|
 |
 |
   Chrome throttle cable, Turbo 350 kickdown cable and cruise cable bracket. Desgined for use with the Edelbrock carburetor shown above. Fits Chevy small block. All three positions are fully length adjustable. Mounts to the back intake manifold bolts on the drivers side of the engine.
Super sturdy, heavy metal design with attractive chrome show car quality finish.

|
 |
 |
   GM throttle cable, Turbo 350 transmission kick down cable bracket.
Designed for use with the Edelbrock carburetor shown above.
All positions are fully length adjustable.
Chrome plated.
Mounts to the drivers side rear carburetor mounting stud.
Easy to install and make for a clean installation.

|
 |
 |
   A pair of throttle return springs.
Universal design.
Engineered to provide positive throttle return for increased safety.
Inner and outer spring are Electro-Nickel bright plated to resist rust.
Includes chrome-plated bracket that attaches to the drivers side, rear carburetor mounting stud.
Springs can also mount to the throttle cable bracket.
The other end of the springs fit into the bottom hole of the carburetors throttle linkage arm.
Can be used with many different throttle cable bracket designs.

|
 |
 |
   GM throttle linkage stud to attach your GM throttle cable to the throttle linkage arm of the Edelbrock carburetor.
Installs into the large upper hole on the carburetors throttle linkage arm and requires a bushing to space the hole.
7/32" diameter threaded stud.

|
 |
 |
   This stud mounts the GM Turbo 350 kick down cable to the Edelbrock carburetors throttle linkage arm.
Slips into the cables slider.

|
 |
 |
   A ball stud throttle stud assortment.
Provides several ball sizes and stud sizes for various non-GM cables.
Attaches to the Edelbrock carburetors throttle linkage arm, in the large upper hole.
Requires a hole bushing for installation.

|
 |
 |
   Edelbrock 1472 Edelbrock carburetor gasket kit.
Fits all Edelbrock Performer Series, Thunder AVS series and Performer EPS Series carburetors.
Includes the gaskets shown.

|
 |
 |
   Edelbrock 1477 Edelbrock carburetor rebuild kit.
Includes parts and gaskets to rebuild all of Edelbrock Performer Series, Performer EPS Series and Thunder AVS series carburetors.
(Floats not included.)

|
 |
 |
   Edelbrock 1469.
Edelbrock carburetor floats.
Fits Edelbrock Performer Series, Thunder AVS Series and Performer EPS Series carburetors.
Includes two floats, two pins and a float setting gauge.

|
 |
 |
   Edelbrock 1473.
Edelbrock Performer Series carburetor linkage kit.
Kit includes 7 links in gold iridite finish and 6 retaining clips.

|
 |